Emulator 1.6 - Revision history

Matt: Reverted edits by Amesycyxa (Talk); changed back to last version by Matt

2010-11-26T19:44:03Z

Reverted edits by Amesycyxa (Talk); changed back to last version by Matt

Amesycyxa at 22:20, 17 November 2010

2010-11-17T22:20:23Z

Matt at 23:50, 9 November 2009

2009-11-09T23:50:57Z

Matt at 23:32, 9 November 2009

2009-11-09T23:32:09Z

Matt at 23:31, 9 November 2009

2009-11-09T23:31:34Z

Matt at 23:28, 9 November 2009

2009-11-09T23:28:01Z

Matt: New page: =New Features= This section describes some of the new features in release 1.6. ==AWID MPR== - The AWID now uses TCP to connect instead of Serial. - Several new commands have been added, ...

2009-11-09T23:16:45Z

New page: =New Features= This section describes some of the new features in release 1.6. ==AWID MPR== - The AWID now uses TCP to connect instead of Serial. - Several new commands have been added, ...

New page

=New Features=
This section describes some of the new features in release 1.6.

==AWID MPR==

- The AWID now uses TCP to connect instead of Serial.
- Several new commands have been added, including Gen2 Portal.
- There is now a welcome message providing information about the reader at startup.

==Alien==

- Speed and RSSI are now supported features for tags.
- Now allows both ON/OFF and 1/0 to be used for commands that toggle between "on" and "off"
- Several Autonomous commands are fixed so they work properly.

==LLRP==

@@ Line 1: / Line 1: @@
->=New Features=
+=New Features=
 This section describes some of the new features in release 1.6.
@@ Line 13: / Line 13: @@
 *Speed and RSSI are now supported features for tags.
-*Now allows both ON/OFF and 1/0 to be used for commands that toggle between &quot;on&quot; and &quot;off&quot;
+*Now allows both ON/OFF and 1/0 to be used for commands that toggle between "on" and "off"
 *Several Autonomous commands are fixed so they work properly.
-*Fixed a problem with the &quot;antennasequence&quot; command that sometimes caused no tags to be read.
+*Fixed a problem with the "antennasequence" command that sometimes caused no tags to be read.
 *GPIO is now enabled by default.
 *Time commands now work for the Alien.
@@ Line 29: / Line 29: @@
 *Added support for the Sirit reader to emulator.

@@ Line 1: / Line 1: @@
-=New Features=
+>=New Features=
 This section describes some of the new features in release 1.6.
@@ Line 13: / Line 13: @@
 *Speed and RSSI are now supported features for tags.
-*Now allows both ON/OFF and 1/0 to be used for commands that toggle between "on" and "off"
+*Now allows both ON/OFF and 1/0 to be used for commands that toggle between &quot;on&quot; and &quot;off&quot;
 *Several Autonomous commands are fixed so they work properly.
-*Fixed a problem with the "antennasequence" command that sometimes caused no tags to be read.
+*Fixed a problem with the &quot;antennasequence&quot; command that sometimes caused no tags to be read.
 *GPIO is now enabled by default.
 *Time commands now work for the Alien.
@@ Line 29: / Line 29: @@
 *Added support for the Sirit reader to emulator.

← Older revision		Revision as of 23:50, 9 November 2009
Line 25:		Line 25:
	*Fixed a problem where sometimes a ROSpec wouldn't start again after being disabled.		*Fixed a problem where sometimes a ROSpec wouldn't start again after being disabled.
	*Fixed a conversion error for a short in _C1G2ReadOpSpecResult		*Fixed a conversion error for a short in _C1G2ReadOpSpecResult
		+
		+	==Sirit==
		+
		+	*Added support for the Sirit reader to emulator.

@@ Line 4: / Line 4: @@
 ==AWID MPR==
-- The AWID now uses TCP to connect instead of Serial.
+*The AWID now uses TCP to connect instead of Serial.
-- Several new commands have been added, including Gen2 Portal.
+*Several new commands have been added, including Gen2 Portal.
-- There is now a welcome message providing information about the reader at startup.
+*There is now a welcome message providing information about the reader at startup.
-- The reader will no longer crash if an invalid command is sent.
+*The reader will no longer crash if an invalid command is sent.
-- Fixed an issue where requesting the temperature would cause the reader to crash.
+*Fixed an issue where requesting the temperature would cause the reader to crash.
 ==Alien==
-- Speed and RSSI are now supported features for tags.
+*Speed and RSSI are now supported features for tags.
-- Now allows both ON/OFF and 1/0 to be used for commands that toggle between "on" and "off"
+*Now allows both ON/OFF and 1/0 to be used for commands that toggle between "on" and "off"
-- Several Autonomous commands are fixed so they work properly.
+*Several Autonomous commands are fixed so they work properly.
-- Fixed a problem with the "antennasequence" command that sometimes caused no tags to be read.
+*Fixed a problem with the "antennasequence" command that sometimes caused no tags to be read.
-- GPIO is now enabled by default.
+*GPIO is now enabled by default.
-- Time commands now work for the Alien.
+*Time commands now work for the Alien.
 ==LLRP==
-- Fixed a problem with ROSpecs accepting an invalid ID number as valid during creation.
+*Fixed a problem with ROSpecs accepting an invalid ID number as valid during creation.
-- Fixed an exception that sometimes occurred when sending a SET_READER_CONFIG command.
+*Fixed an exception that sometimes occurred when sending a SET_READER_CONFIG command.
-- Fixed a problem where sometimes a ROSpec wouldn't start again after being disabled.
+*Fixed a problem where sometimes a ROSpec wouldn't start again after being disabled.
-- Fixed a conversion error for a short in _C1G2ReadOpSpecResult
+*Fixed a conversion error for a short in _C1G2ReadOpSpecResult

@@ Line 7: / Line 7: @@
 - Several new commands have been added, including Gen2 Portal.
 - There is now a welcome message providing information about the reader at startup.
 ==Alien==
@@ Line 14: / Line 16: @@
 - Several Autonomous commands are fixed so they work properly.
 - Fixed a problem with the "antennasequence" command that sometimes caused no tags to be read.
 ==LLRP==
@@ Line 20: / Line 24: @@
 - Fixed an exception that sometimes occurred when sending a SET_READER_CONFIG command.
 - Fixed a problem where sometimes a ROSpec wouldn't start again after being disabled.